# Dominican Republic Power & Grid Engineering Profile

> Preliminary country engineering reference. Connection voltage, short-circuit duty, earthing and regulatory approval require current project-specific confirmation from the local TSO/DSO.

**Canonical:** https://voltformer.com/country-profile/dominican-republic - markdown: https://voltformer.com/country-profile/dominican-republic.md - ISO: DO

## Electrical system

- Frequency: 60 Hz
- Transmission voltage candidates: 138, 69 kV
- Distribution voltage candidates: 12.47, 7.2, 4.16 kV
- Low-voltage candidates: 480, 208, 120 V
- Typical vector groups: Dyn1, YNd1
- Typical tap range: ±2x2.5%

## Power quality and grid operating limits

- Normal frequency operational tolerance: ±0.2 Hz
- Steady-state voltage tolerance: ±10 %
- Maximum continuous THD-V at MV PCC: ≤ 5 %
- Maximum negative sequence voltage unbalance: ≤ 2 %
- Grid code power factor range at PCC: 0.95 cap - 0.95 ind

## Substation short-circuit and earthing

- Typical MV bus symmetrical fault rating: 20 kA RMS (1s / 3s)
- Typical HV substation breaking capacity: 40 kA RMS
- MV neutral earthing regime: solid
- LV customer earthing system: TN-C-S

## Dielectric insulation coordination

- MV Lightning Impulse Withstand (BIL): 75 kV peak (1.2/50 µs)
- MV Power Frequency Withstand (1 min): 28 kV RMS (50/60 Hz)
- Minimum specific creepage distance (SPS): 20 mm/kV phase-to-phase
- IEC 60815 pollution severity classification: Class II (Medium)

## Electromechanical and environmental design

- Design peak ground acceleration (PGA): 0.25 g (IEEE 693 / Eurocode 8)
- Basic design wind speed: 45 m/s (~162 km/h)
- Substation acoustic noise limit at 1m: ≤ 62 dBA
- Extreme minimum design ambient temperature: 15 °C
- Maximum 24-hour daily average ambient temperature: 30 °C
- Maximum solar radiation heat flux: 1000 W/m²
- Atmospheric corrosivity category (ISO 12944-2): C3 (Medium)
- MV bushing connector interface standard: IEEE 386 (200A Loadbreak / 600A Deadbreak)

## Standards and efficiency

- Standards/codes: IEEE C57, ETED Grid Code, SIE Directives
- Regulatory standard code: IEC 60076 Loss Guidelines / National Grid Code
- Benchmark minimum efficiency (PEI / 1000 kVA): 99.38 %
- Regulatory enforcement: grid-code-regulated
- Efficiency regulation notes: ETED & Dominican Electricity Superintendence (SIE) Standards

## Grid energy economics and carbon intensity

- Benchmark industrial electricity tariff: $0.165 / kWh (TCO capitalized loss A & B factor evaluation)
- Grid carbon emission intensity: 510 g CO2eq/kWh (Scope 2 lifecycle emissions assessment)
- National renewable energy share: 22.4 % (grid inertia & inverter-based resource impact)
- Primary official statistical source: ETED / SIE Dominican Republic

## Advanced engineering calculation parameters

- Substation network X/R ratio: 9 (IEC 60909 fault impedance modeling)
- Dynamic peak short-circuit factor (κ per IEC 60909): 1.72 (ip = κ · √2 · Ik'' electrodynamic force)
- Regional reference apparent soil resistivity (ρ): 260 Ω·m (IEEE 80 / IEC 61936-1 substation earthing)
- Recommended transformer harmonic K-factor rating: K-4 (ANSI/IEEE C57.110 eddy derating)

## Official public regulatory and grid authorities

- [ETED - Empresa de Transmisión Eléctrica Dominicana Código de Red](https://www.eted.gov.do) (transmission-operator)
- [SIE - Superintendencia de Electricidad República Dominicana](https://sie.gob.do) (energy-regulator)

## Grid operators

- ETED
- Edeeste
- Edesur
- Edenorte

## Climate design reference

- Reference ambient: 40 °C
- Maximum design ambient: 42 °C
- Standard altitude basis: 500 m
- Notes: Caribbean hurricane corridor (Category 5 wind resistance), marine salt spray, pad-mounted transformers.

## Typical applications

- Caribbean Resort & Hospitality Infrastructure

## Safe project candidates

- Nominal voltage candidates: 12.47, 7.2, 4.16, 138, 69 kV
- LV utilization-voltage candidates (line-to-line and/or line-to-neutral; confirm the transformer's rated terminal voltage and phase configuration): 480, 208, 120 V
- Vector group candidates: Dyn1, YNd1
- Automatic nominal voltage: withheld - point of connection required

## Mandatory project verification

- pointOfConnectionVoltage
- prospectiveShortCircuitCurrent
- systemEarthingAndNeutral
- insulationCoordination
- protectionCoordination
- powerQualityAndHarmonics
- siteAmbientAndAltitude
- seismicWindPollution
- utilityApproval

Machine data: https://voltformer.com/api/v1/countries/DO - all profiles: https://voltformer.com/country-grid-standards.json - grid checker: https://voltformer.com/grid-standards